Concrete Driveways Rowville 3178 | Local Driveway Concreters

Concrete driveways in Rowville, 3178

Concrete driveway installation for Rowville homes across the 1980s and 90s estates either side of Wellington Road, from the streets around Stud Park to the larger blocks towards Lysterfield. Every driveway is properly prepped and reinforced with steel mesh. Knox City Council vehicle crossing and asset protection permits may be required.

Ground conditions in Rowville

Rowville’s estate driveways are reaching the age where the original concrete has cracked and dropped at the crossover, usually because the base has washed out. A replacement is excavated to firm ground and prepped, with base material brought in and compacted where the ground needs it, a membrane where required and steel mesh reinforcement, with control joints to direct any movement.

Double driveways in Rowville

Most Rowville homes have a double garage and a wide driveway of 70 to 90 square metres. On a driveway that size the fall and the joint layout matter more than on a single, and a grated drain across the garage threshold is specified where the block falls in. Driveways carrying a caravan or boat are specified at 125mm with heavier mesh.

Finishes suited to Rowville

Exposed aggregate in charcoal or mid grey stone is the most common specification for replacement driveways in Rowville. A broom finished plain driveway performs identically underground at around a third less.

Concrete driveway cost in Rowville

A standard single driveway in Rowville is 40 to 50 square metres. Plain concrete with a broom or trowel finish runs $95 to $130 per m², coloured concrete $115 to $160 and exposed aggregate $130 to $185, all supplied and laid with the base preparation described above. Removal of an existing driveway adds $35 per m². A replaced single driveway in exposed aggregate typically falls between $7,500 and $10,000, and the quote issued after the site measure is fixed. The driveway cost guide sets out what moves the price.

Knox City Council crossover permits

Bayswater, Boronia, Ferntree Gully, Rowville, Wantirna and Scoresby. Lots of 1970s and 80s driveways here at the end of their life, often with a sunken crossover where the base has washed out. Knox is straightforward on permits.

Knox needs a vehicle crossing permit and an asset protection permit. Crossovers must match the standard drawing and council inspects before concrete is placed.

Council permit information

Nearby suburbs we also cover

Bayswater. See the full Outer East list.

What we pour

Driveways in Rowville

Every driveway gets a proper base, mesh, expansion cuts and a drainage fall. The finish is up to you.

Freshly poured plain grey concrete driveway

Plain concrete driveways

Broom finishSteel trowel25 MPa

Broom or steel trowel finish, steel mesh reinforced, 25 MPa concrete. The most economical driveway and the easiest to maintain.

From $95 to $130 per m²

See plain concrete driveways

Exposed aggregate concrete driveway leading to a double garage

Exposed aggregate driveways

Local and imported stoneSealedNon-slip

Decorative stone revealed at the surface and sealed after cure for colour and grip. The most specified finish for street-facing driveways.

From $130 to $185 per m²

See exposed aggregate driveways

Coloured concrete driveways

Full depth colourStencil patternsCharcoal

Oxide pigment through the full depth of the slab so the colour cannot wear off. Charcoal is the most common specification for Melbourne homes.

From $115 to $160 per m²

See coloured concrete driveways

Concrete truck discharging during a driveway replacement pour

Driveway removal and replacement

DemolitionDisposalTree roots

Existing concrete, pavers or asphalt removed and disposed of, new driveway poured. Typically two days on site.

From $130 to $175 per m²

See driveway removal and replacement

Process

From enquiry to a driveway you can park on

Enquiry
Call or send the form with the suburb and the type of driveway. A site measure is booked, usually within a few days.
Site measure and fixed quote
Dimensions, fall, access and drainage are assessed on site. A council crossover permit may be required for the street section. The written quote is fixed.
Preparation and pour
Existing surface removed and the area prepped, with base material brought in where needed. Mesh laid, crossover formwork inspected by council, then the pour. Most residential driveways are one day on site.
Cure and seal
Vehicles off for seven days. Exposed aggregate is sealed after the concrete has cured.

Specification

How our driveways are built

Two quotes can look the same on paper and be very different underground. This is what is included in ours. Full specification.

Preparation

The old surface removed and the area prepped, with base material brought in and compacted where the ground needs it. Preparation is where most cheap driveways fail.

Reinforcement

Steel mesh reinforcement and 25 MPa concrete, with a thicker slab and heavier mesh quoted where caravans and trucks will park.

Drainage

A fall away from the house, and a grated drain across the garage threshold where the block falls in.

Joints and cure

Control joints cut to direct any movement. Seven days before vehicles, and exposed aggregate sealed after cure.

Rowville driveway questions

Is a permit required for a driveway in Rowville?

Knox needs a vehicle crossing permit and an asset protection permit. Crossovers must match the standard drawing and council inspects before concrete is placed.

What does a concrete driveway cost in Rowville?

Plain concrete $95 to $130 per m², coloured $115 to $160, exposed aggregate $130 to $185, supplied and laid with base and reinforcement. A typical Rowville single driveway is between $4,500 and $8,500 depending on finish and whether an existing driveway is removed.

How quickly can a site measure be arranged in Rowville?

Site measures in Rowville are generally scheduled within a few days of enquiry.